Location: Barrie
-
.157 X 1-7/8″ POWDER-DRIVEN PIN GALV /HUN
The minimum effective shank length must equal or exceed the sum of the thickness of the attached material and the minimum embedment depth Code listed per ICC-ES ESR-2138, Florida FL15730 and LA RR25469 Designed for use with Simpson Strong-Tie® powder-actuated tool systems as well as other common tools The PDPA-MG models are mechanically galvanized for additional corrosion protection
-
.22 X 10″ T-40 INTERIOR STRUCTURAL SCREW ECOAT /HUN
SawTooth® point ensures fast starts, reduces installation torque and eliminates the need for predrilling in most applications Serrated thread reduces splitting and damage Low-profile, large-diameter washer head with nibs provides maximum bearing area and makes countersinking easy 6-lobe, T40 drive provides positive engagement that makes the screw easy to drive and improves bit life (replacement driver bit: BIT40T-134) Size identification on all Simpson Strong-Tie screws
-
.22 X 12″ T-40 INTERIOR STRUCTURAL SCREW ECOAT /HUN
SawTooth® point ensures fast starts, reduces installation torque and eliminates the need for predrilling in most applications Serrated thread reduces splitting and damage Low-profile, large-diameter washer head with nibs provides maximum bearing area and makes countersinking easy 6-lobe, T40 drive provides positive engagement that makes the screw easy to drive and improves bit life (replacement driver bit: BIT40T-134) Size identification on all Simpson Strong-Tie screws
-
.22 X 3″ T-40 DOUBLE BARRIER STRUCURAL SCREW /HUN
SawTooth® point ensures fast starts, reduces installation torque and eliminates the need for predrilling in most applications Bold thread design provides superior holding power Underhead nibs offer greater control when seating the head Large low-profile washer head provides maximum bearing area (0.75″ head dia.)
-
.22 X 4″ T-40 DOUBLE BARRIER STRUCURAL SCREW /HUN
SawTooth® point ensures fast starts, reduces installation torque and eliminates the need for predrilling in most applications Bold thread design provides superior holding power Underhead nibs offer greater control when seating the head Large low-profile washer head provides maximum bearing area (0.75″ head dia.) Size identification on all SDWS screw heads 6-lobe T40 drive provides positive engagement that makes the screw easy to drive and improves bit life (replacement driver bit — BIT40T-134-RC) Double-barrier coating provides corrosion resistance equivalent to hot-dip galvanization, making it suitable for certain exterior and preservative-treated wood applications, as described in the evaluation report
-
.22 X 5″ T-40 DOUBLE BARRIER STRUCURAL SCREW /HUN
SawTooth® point ensures fast starts, reduces installation torque and eliminates the need for predrilling in most applications Bold thread design provides superior holding power Underhead nibs offer greater control when seating the head Large low-profile washer head provides maximum bearing area (0.75″ head dia.)
-
.22 X 6″ T-40 DOUBLE BARRIER STRUCURAL SCREW /HUN
SawTooth® point ensures fast starts, reduces installation torque and eliminates the need for predrilling in most applications Bold thread design provides superior holding power Underhead nibs offer greater control when seating the head Large low-profile washer head provides maximum bearing area (0.75″ head dia.) Size identification on all SDWS screw heads
-
#17W 3/8 20DEG SWIVEL ROD EXT
Carbon Steel
-
#416 12 RETAINING STRAP
For determining min. length of strap, add two inches to width of flange.
-
1-3/4 X .092 HDG COIL NAIL 4500 / BOX
Length: 1-3/4″ Shank: .094
-
1″ X 4′ ADJUSTABLE TIE DOWN STRAP 2/PACK
• Steel J & S hooks, one on each end • Release cam buckle • Maximum stretch from 12″ to 50″ • EPDM 6″ natural rubber stretches 50% its length • Capacity: 70lb (31kg)
-
1″ X 6″ HAND SEAMER
Fully Heat-Treated And Tempered Double Layered And Non-Slip Handles
-
1″ X 6″ IRWIN TRI FLUTE SPEEDBORE DRILL BIT
A fast speedbor spade bit that features a Tri-Flute design with a fast chip ejection Cutting spurs have 3 cutting edges Grooved hex shank prevents slipping Fits all standard 1/4-inch quick change chucks Full screw tip allows the bit to self feed
-
1″ X 9″ HAND SEAMER
Fully Heat Treated And Tempered Double Layered And Non-Slip Handles
-
1/2 TEFLON THREAD TAPE
We offer both 1/2″ wide and 3/4″ wide.
-
1/2 X 5″ TITEN CONCRETE SCREW ANCHOR ZINC /C
Qualified for static, wind and seismic loading conditions Thread design undercuts to efficiently transfer the load to the base material Standard fractional sizes Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved Reuse of the anchor will not achieve listed loads and is not recommended
-
1/2 X 6″ SLEEVE-ALL HEX HEAD ANCHOR /C
Material Carbon steel or stainless steel Finish Carbon steel anchors are zinc plated
-
1/2 X 7 STRONG-BOLT 2 WEDGE ANCHOR SIMPSON /HUN
Chamfered top designed to prevent mushrooming during installation Qualified for static and seismic loading conditions (seismic design categories A through F) Suitable for horizontal, vertical and overhead applications Qualified for minimum concrete thickness of 3 1/4″, and lightweight concrete-over-steel deck thickness of 2 1/2″ and 3 1/4″ Standard (ANSI) fractional sizes: fits standard fixtures and installs with common drill bit and tool sizes Tested per ACI355.2 and AC193
-
1/2 X 8 TITEN CONCRETE SCREW ANCHOR GALV /C
Qualified for static, wind and seismic loading conditions Thread design undercuts to efficiently transfer the load to the base material Standard fractional sizes Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved Reuse of the anchor will not achieve listed loads and is not recommended
-
1/2″ HAMMER DRILL
Items Included: Keyless Drill Chuck (196193-0), Side Handle (153503-4), Plastic Carrying Case (824811-7)
-
1/2″ TEFLON TAPE,WHITE/EA
Works for both water and air
-
1/2″ X 10″ STRONG BOLT 2 WEDGE ANCHOR SIMPSON /HUN
Chamfered top designed to prevent mushrooming during installation Qualified for static and seismic loading conditions (seismic design categories A through F) Suitable for horizontal, vertical and overhead applications Qualified for minimum concrete thickness of 3 1/4″, and lightweight concrete-over-steel deck thickness of 2 1/2″ and 3 1/4″ Standard (ANSI) fractional sizes: fits standard fixtures and installs with common drill bit and tool sizes Tested per ACI355.2 and AC193
-
1/2″ X 3-3/4″ STRONG BOLT 2 WEDGE ANCHOR SIMPSON /HUN
Chamfered top designed to prevent mushrooming during installation Qualified for static and seismic loading conditions (seismic design categories A through F) Suitable for horizontal, vertical and overhead applications Qualified for minimum concrete thickness of 3 1/4″, and lightweight concrete-over-steel deck thickness of 2 1/2″ and 3 1/4″ Standard (ANSI) fractional sizes: fits standard fixtures and installs with common drill bit and tool sizes Tested per ACI355.2 and AC193
-
1/2″ X 4″ TITEN CONCRETE SCREW ANCHOR GALV /C
Qualified for static, wind and seismic loading conditions Thread design undercuts to efficiently transfer the load to the base material Standard fractional sizes Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved Reuse of the anchor will not achieve listed loads and is not recommended
-
1/2″ X 4″ TITEN CONCRETE SCREW ANCHOR ZINC /C
Qualified for static, wind and seismic loading conditions Thread design undercuts to efficiently transfer the load to the base material Standard fractional sizes Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved Reuse of the anchor will not achieve listed loads and is not recommended
-
1/2″ X 5″ TITEN CONCRETE SCREW ANCHOR GALV /C
Qualified for static, wind and seismic loading conditions Thread design undercuts to efficiently transfer the load to the base material Standard fractional sizes Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved Reuse of the anchor will not achieve listed loads and is not recommended
-
1/2″ X 6″ IRWIN TRI FLUTE SPEEDBORE DRILL BIT
A fast speedbor spade bit that features a Tri-Flute design with a fast chip ejection Cutting spurs have 3 cutting edges Grooved hex shank prevents slipping Fits all standard 1/4-inch quick change chucks Full screw tip allows the bit to self feed
-
1/2″ X 6″ TITEN CONCRETE SCREW ANCHOR GALV /EA
Qualified for static, wind and seismic loading conditions Thread design undercuts to efficiently transfer the load to the base material Standard fractional sizes Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved Reuse of the anchor will not achieve listed loads and is not recommended
-
1/2X3 TITEN ANCHOR /C
Qualified for static, wind and seismic loading conditions Thread design undercuts to efficiently transfer the load to the base material Standard fractional sizes Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved Reuse of the anchor will not achieve listed loads and is not recommended
-
1/4 BARD 1/4 MANUAL COUPLER N TYPE
A tubular valve is standard for all body sizes for improved flow. Plugs are machined from solid steel and brass. Steel plugs are hardened and zinc plated to provide maximum service life. This series confirms to the MIL-4109C Interchange Standard. Please note, couplers designated with suffix ‘B’ have brass valves.
-
1/4 BODY X 3/8 MALE THREADED END COUPLER
A tubular valve is standard for all body sizes for improved flow. Plugs are machined from solid steel and brass. Steel plugs are hardened and zinc plated to provide maximum service life. This series confirms to the MIL-4109C Interchange Standard. Please note, couplers designated with suffix ‘B’ have brass valves.
-
1/4 X 1-1/2 CS HAMMER DRIVE PIN ANCHOR
Flat head Zinc plated steel body AISI 1038 carbon steel pin Tamper-proof 100 per package
-
1/4 X 1-5/8 TITEN HD ROD HANGER 50/BX
Thread design undercuts to efficiently transfer the load to the base material Serrated cutting teeth and thread design enable quick and easy installation Specialized heat-treating process creates tip hardness to facilitate cutting while the anchor body remains ductile Designed to install using a rotary hammer or hammer drill with standard ANSI drill bits — no special tools required Installs with standard-sized sockets Code listed for cracked and uncracked concrete applications under the 2015, 2012 and 2009 IBC/IRC, per ICC-ES ESR-2713 FM listed
-
1/4 X 1-7/8 TITEN CONCRETE SCREW ANCHOR ZINC /C
Qualified for static, wind and seismic loading conditions Thread design undercuts to efficiently transfer the load to the base material Standard fractional sizes Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved Reuse of the anchor will not achieve listed loads and is not recommended
-
1/4 X 1/4 FEMALE NPT COUPLER
A tubular valve is standard for all body sizes for improved flow. Plugs are machined from solid steel and brass. Steel plugs are hardened and zinc plated to provide maximum service life. This series confirms to the MIL-4109C Interchange Standard. Please note, couplers designated with suffix ‘B’ have brass valves.
-
1/4 X 2″ NAILON PIN DRIVE ANCHOR ZINC /C
Zinc Nailon anchors are low-cost, easy-to-install anchors for applications under static loads.
-
1/4 X 3-1/2″ TITEN HD HEAVY DUTY SCREW ANCHOR / 100 PIECES
Qualified for static, wind and seismic loading conditions Thread design undercuts to efficiently transfer the load to the base material Standard fractional sizes Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved Reuse of the anchor will not achieve listed loads and is not recommended
-
1/4 X 3″ NAILON PIN DRIVE ANCHOR ZINC /C
Zinc Nailon anchors are low-cost, easy-to-install anchors for applications under static loads.
-
1/4 X 4 TITEN CONCRETE SCREW ANCHOR ZINC /C
Qualified for static, wind and seismic loading conditions Thread design undercuts to efficiently transfer the load to the base material Standard fractional sizes Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved Reuse of the anchor will not achieve listed loads and is not recommended
-
1/4″ DIE GRINDER, VS
Included: Collet Cone Set 1/4” (192986-3), Wrench 13 (781203-2), Wrench 19 (781206-6), Side Handle (192985-5)
-
1/4″ NPT FEMALE FLAT HEX TRIPLE MANIFOLD WITH COUPLINGS
FEATURES Solid Brass Manifold Flat Hex Shape 1/4″ NPT Female Inlet Three 1/4″ NPT Female Outlets
-
1/4″ NPT X 1/8″ MALE HOSE BARD
We offer hose barbs and menders as straights, elbows, and tees.
-
1/4″ X 3″ TITEN HEAVY DUTY SCREW ANCHOR ZINC /C
Qualified for static, wind and seismic loading conditions Thread design undercuts to efficiently transfer the load to the base material Standard fractional sizes Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved Reuse of the anchor will not achieve listed loads and is not recommended
-
1/4ID HOSE BARB SPLICER
HOSE SIZE: 1/4″ MATERIAL: Brass SHAPE: Straight WEIGHT: 0.02 lb
-
1/4X1-1/4 HEX CONCRETE /M BULK
Typical applications: Conduit clips Strapping or 2×4 studs Metal shelf – uprights Cladding Window frames Brick ties Materials: Carbon Steel: AISI C1022 UTS: 73 ksi (503 MPa) Case Hardened (HRC: 30 – 42) Stainless Steel: AISI 410 C UTS: 78 ksi (538 MPa)
-
1/4X1-3/4 HEX CONCRETE /M BULK
Typical applications: Conduit clips Strapping or 2×4 studs Metal shelf – uprights Cladding Window frames Brick ties Materials: Carbon Steel: AISI C1022 UTS: 73 ksi (503 MPa) Case Hardened (HRC: 30 – 42) Stainless Steel: AISI 410 C UTS: 78 ksi (538 MPa)
-
1/4X2-1/4 HEX CONCRETE /M BULK
Typical applications: Conduit clips Strapping or 2×4 studs Metal shelf – uprights Cladding Window frames Brick ties Materials: Carbon Steel: AISI C1022 UTS: 73 ksi (503 MPa) Case Hardened (HRC: 30 – 42) Stainless Steel: AISI 410 C UTS: 78 ksi (538 MPa)
-
10 X 2-1/2IN QUICKDRIVE RED T25 RIBBED FLAT WOOD SCREW /1000
Low-torque threads Ribbed-head design countersinks easily and provides a clean, finished appearance High-low threads with Type-17 point provides fast starts Optimized threads for lumber Quik Guard® coating provides corrosion resistance for exterior and certain preservative-treated wood applications Meets the performance requirements of ICC-ES AC257 exposure conditions 1 and 3 Colors to blend in with most woods